Why microcement cracks, and how to prevent it

Most cracks begin in what sits underneath. The coating only shows what the base is doing.

By Kret · Updated 2 Nov 2026 · 3 min read
Close-up of trowelled microcement surface
Close-up · Trowelled microcement
Short answer

Microcement usually cracks because the base moves, not because the coating fails. It is a thin layer bonded to whatever is below, so movement, old cracks and missing joints come through. Good preparation, mesh and respected movement joints reduce the risk, but no thin mineral finish is crack-proof.

The main causes

CauseWhat you seeHow to reduce it
Base movementCracks that follow the substrate1Stable base, repaired before coating
Missing movement jointsStraight vertical cracks2Carry building joints through
Drying too fastFine surface crazing3Control sun, wind and air conditioning
Too much water in the mixWeak, shrinking coat3Follow the mix exactly
Different backgrounds meetingCracks along a junction2Mesh across the junction
Loose tileCracks over grout linesFix or remove loose tile first

Reading a crack

The shape of a crack says a lot about its cause. Use this as a first guide, not a diagnosis.23

What you seeLikely meaning
Fine web of linesShrinkage while curing
Straight vertical lineMissing movement joint
Diagonal from a door or window cornerMovement around the opening
Line following a gridOld tile or grout showing through
Line where wall meets columnTwo materials moving differently
Crack that keeps growingActive movement. Have it inspected

What is normal

Cement shrinks as it cures, so very fine lines can appear. For mineral renders, Sika describes hairline cracks under 0.2 mm as not harmful to the system.2 That guidance is for render, not microcement, but the principle is similar. A wider crack, or one that keeps growing, points to movement below and should be inspected.2

Where to look

Movement cracks usually appear at wall corners and doorways.3 Diagonal cracks from windows and doors point to the structure behind.2

Why Thai buildings need extra care

Much of Bangkok is a concrete frame filled with blockwork, so two materials with different movement meet at every column and beam. Sika recommends mesh where materials of different density meet, for this reason.2 Add heat, rain and a slab that may still be drying, and these lines are the first places to look.

Moisture matters as well. Sika warns about excessively wet substrates, and a wall that has been rained on during construction can take time to dry.2 Air conditioning that starts the day the crew leaves can pull moisture out faster than the coat likes, so ask how to bring a new room into use.

What good preparation includes

  • Check the base, and repair cracks and loose areas.
  • Use fibreglass mesh where the system calls for it, while remembering it has limits. One installer says it can only hold for so long.4
  • Keep existing building joints. Never trowel over a movement joint.
  • Give each coat time to cure, and protect it from direct air conditioning and sun.
Raw clay plaster with fine cracks left as part of the finish
Raw texture, where fine cracks are part of the design.

If you can’t accept any cracks

Be honest about the building. On a new structure still settling, or on a suspended timber floor, wait or choose another finish. Tile may be calmer, as Microcement vs tile explains.

If a crack appears

  • Do not sand or fill it yourself.
  • Photograph it with a ruler beside it, and note the date.
  • Mark the ends lightly, and check again in a few weeks.
  • Note any change after heavy rain or building work nearby.
  • Send this to your installer, because active movement must stop before repair.2

Agree what is acceptable beforehand

The best time to discuss cracks is before work starts. Ask what counts as a defect, how repairs are done and how they will look. For specifiers, put this in the document. See How to specify decorative finishes.

Questions

Is a hairline crack a defect?

It depends on width, location and your warranty. Very fine lines can be normal in mineral finishes. Ask your installer to assess it.

Can cracks be repaired?

Usually, but the repair may show because the finish is handmade.1

Does mesh stop cracking?

It helps, but it cannot hold back real movement in the base.4

Will a crack get worse?

Shrinkage lines usually settle. Cracks from structural movement can keep changing until the movement stops.2

Sources

  1. Qanvast: What Is Microcement? A Complete Guide for Singapore Homeowners (2026)
  2. Sika: Cracks in mineral render finishes, best practice
  3. Cemcrete: The big question, will it crack?
  4. Homebuilding & Renovating: Polished concrete vs microcement flooring

Hold microcement before you specify it.

Hand-made samples in your colours, delivered to your studio. For larger projects we trowel a full-size panel on site.

Order a sample